10 memory digital electronic stopwatch operation instruction

Features:

1. The stopwatch function (for measuring memory)

L the longest measurement time he said '59 ", minimum reading value of 1/100 of a second.

L can achieve 11 each section of the same section measurement and continuous time measured in two ways.

L can remember and shows a 10 hour time respectively.

Timer 2.

L three ways: the countdown, countdown, countdown to zero after the first is timing.

L countdown setting time and time is longest time were 23:59 '59 ".

3. The metronome

With 10 taps/min, 20 / min, 30 taps per minute, 40 per minute, 50 taps per minute, 60 / min, 70 / min, 100 / min, 80 pat taps/min, 120 / min, 160 / min, 180 pat/points, 240 points, a total of 13 kinds of selection of the beat.

4. The clock function

L display content: hours, minutes, seconds, month, day, week, year

L can choose 12 or 24 hours display.

5. Set the alarm function

L can accurate time

L can be set rhythm: four beats per second, for 30 seconds

Second, the use method

1. According to the new location and function

S1 START, STOP, adjust the START/STOP

S2 choose SELECT

S3 segment, Settings, zero LAP/RESET/SET

S4 function conversion MODE

2. The stopwatch (measuring the memory function)

According to the state S4 table in stopwatch function

(1) basic stopwatch

L press S1 a stopwatch to start time, end measurement S1 to zero.

L press S1 starting, first determine end press S1 to stop; Press S1 accumulative total timing, again press S1 to stop again; ...... So start stop in a row, the last stop after implementation accumulative time measurement.

According to the S3 to zero.

(2) the same start time measurement

According to S2 seconds in the same starting time timing. Press S1 to start time, end of the first paragraph hold S3, the alternating phase ordinal number and the first period of running time. Let go of S3 is shown in the original machine run time state. Repeat the above operation can be measured more than the same start time tn, can measure up to 10 hours of time. Last end of the period, according to the S1 stop timing run, show the running time, the last time press S3 to zero again.

This function is a total of 11 measurable same starting period of time.

(3) the continuous piecewise timing

According to the S2 table continuous piecewise timing state. Press S1 to start time, end of the first paragraph hold S3, i.e. alternating phase ordinal number and the first period of running time. Let go of the S3 in the second paragraph of time state. Repeat the above operation can be measured more segmented time in a row. Last time end stops by S1, displayed the last a period of time, in the S3 to zero.

This function a total of 11 segmented time can be obtained.

(4) 10 times the memory display

With the above two measurement, activates the S3 is to write down every time the measurement data. When the last a period of time after the press S1 to stop time, and then click the S2 that alternates between the first period of ordinal number and running time. According to the second under S2 or alternate displays the second period of ordinal number and running time. Repeat the above operation to show ordinal number and time for the last time. Press S2 namely again to display the first paragraph. So, finally according to the S3 after zero.

This function can memory shows up to 10 time data.

3. The timer

Press the S4 table in time

(1) the countdown

Press S3 2 seconds, make the table is in a state of "seconds" adjustment (second display flashing), press S1 set the second time. According to the table S3 in "points" adjustment state (display flashing), press S1 set the timing. Press S3 making table and "when" adjustment status (display flashing), press the S1 set hours timer. According to the S3 set to complete. According to S1 begin to count down time, for that is the end of the countdown two noise, for 30 seconds of the timing signal. Press S1 to stop timing, again according to the state of S3 to restore the original setting.

(2) cycle countdown

According to the S2 make table in a state of cycle countdown.

With (1) set up operation timing of time.

According to S1 began circulating countdown, each end of the countdown is a regular ring, but still run the countdown, continuous cycle. According to S1 stop the countdown, according to the S3 to restore the original Settings.

(3) the first countdown, then is timing

According to S2 countdown begins countdown to zero, and then start timing. According to S1 is stop timing, according to the S3 to restore the original Settings.

4. The metronome

According to the S4 put table in the beat. Press S3 select the beat frequency 10 taps/min to 240 per minute, according to the S1 is beat frequency chirping, beat frequency display flashing at the same time, according to the S1 is stopped.

5. The clock function

(1) shows

Press the S4 table in clock timing state, display the hour. According to S1 showed that month, day, week, according to S1 to restore the hour show.

(2) to adjust

In the state display hour, S3 2 seconds, make the table in the second adjustment state (second display flashing), seconds, adjusted by S1 state, adjusted by the table S3 in points according to the adjusted score S1. According to the table S3 in the adjustment state, press S1 to adjust. According to the table S3 in year adjustment state, press S1 to adjust. In according to the table S3 in adjusting state, press adjust in S1. According to the table S3 in date adjustment state, press S1 adjustment date. According to the S3 is complete, minutes and seconds, after the adjustment of the year, month, day, week automatically adjust. Choose by S3 choose 12/24 hours, 12 hours when the system will display A or P symbol on the left.

6. Set the alarm function

Press the S4 put table in alarm state

(1) the timing alarm Settings

According to S2 choose four set the time, according to S1 2 seconds, began to set alarm time setting state. , like "clock" adjustment, complete points, when the set, complete set as S3. Press S1 to choose again, there are rings at regularly, symbol appears)))), or no regular rings at symbol appears (not), repeat the above operation order, schedule alarm can be set up the remaining three sections.

(2) the punctual time setting

Press S3 select one hour eventually "bring" symbol (out) or without the punctual alarm symbol appears (not) working condition.

Three, maintenance

1. Always keep a stopwatch cleaning and coating is bright and clean.

2. Avoid flooding, be affected with damp be affected with damp, avoid violent vibration and impact, avoid high temperature.

3. The battery life and the length of time of use. When found, liquid crystal display (LCD) said the battery is used up, need to change new battery. This table with 3 v lithium battery, please use the same specifications of the battery. 3 v lithium battery reference song: CRR2032 (Φ 20 x 3.2)

After u change the battery, please use tweezers short-circuit RST point to reset the stopwatch function.